
Internal Limb Lengthening with a Motorised Nail
FITBONE is a German developed, fully implantable limb lengthening system that allows gradual bone lengthening without external fixation. It may be used for limb length discrepancy, deformity correction, stature lengthening, and other conditions that require planned bone lengthening.
The system uses a motorised intramedullary nail connected to a receiver beneath the skin. An external transmitter transfers energy through the skin to activate the nail. As all implanted components remain beneath the skin, there are no external pins or pin sites during treatment.
What Is Fitbone?
Fitbone consists of an intramedullary lengthening nail, a receiver placed beneath the skin, and an external Control Set. The nail is inserted into the central canal of the bone and secured with locking screws.
When the transmitter is positioned over the receiver, energy passes through the skin and activates the motor inside the nail. The nail extends gradually at the osteotomy site, where new bone forms through distraction osteogenesis. The energy transmission is not normally felt by the patient.
Fitbone Overview
- Device
Fully implantable motorised intramedullary nail - Control
External transmitter and subcutaneous receiver - Rate of distraction
Usually 27 impulses across three daily sessions, approximately 1 mm per day - Mechanical capacity
Up to 8 cm, depending on implant selection - Weight bearing
Partial weight bearing, generally limited to 20 kg during distraction and early healing - MRI
MR unsafe while the system is implanted - Implant removal
Required after consolidation, commonly 12 to 18 months after implantation
How Is the Bone Lengthened?
Lengthening usually begins five to ten days after surgery. The patient places the transmitter over the receiver and performs the number of impulses prescribed by the surgeon.
The standard rate is approximately 1 mm per day. At this rate, 6 cm takes about 60 days and 8 cm takes about 80 days. The prescribed rate may be reduced or paused according to bone formation, joint movement, muscle flexibility, nerve response, pain, and X ray findings.
The distraction schedule must be followed carefully. Lengthening too slowly can lead to premature bone bridging, while lengthening too quickly can affect new bone formation and place the nerves and blood vessels under excessive tension.
How Much Length Can Be Achieved?
The mechanical capacity of the FITBONE system can reach 8 cm, depending on the implant used. This does not mean that 8 cm is suitable for every patient or every bone.
For bilateral femoral stature lengthening, a target of up to 8 cm may be considered when bone formation, joint movement, and soft tissue flexibility remain satisfactory.
Tibial lengthening requires a more conservative target. The muscles and tendons of the lower leg have less tolerance for distraction, particularly around the ankle and Achilles tendon. At ILLRC, the target for bilateral tibial stature lengthening is generally kept around 5 cm.
The final amount is based on clinical tolerance rather than the maximum extension of the nail. Treatment may be stopped before the planned target if bone formation, nerve function, joint movement, or soft tissue flexibility begins to deteriorate.
The FITBONE Treatment Process
1. Clinical Assessment and Planning
Planning includes the indication for surgery, medical history, standing alignment X rays, bone dimensions, bone quality, joint movement, muscle flexibility, body weight, and expected rehabilitation requirements.
The bone canal must have sufficient length and diameter for stable nail placement. The planned amount of lengthening is set only after the bone and soft tissues have been assessed.
2. Surgery and Hospital Care
The bone is divided through a controlled osteotomy. The Fitbone nail is inserted into the bone canal and secured with locking screws. A receiver connected to the nail is placed beneath the skin.
Patients usually remain in hospital for five to seven days for pain control, wound review, early physiotherapy, and mobility training.
3. Lengthening
The distraction phase usually begins five to ten days after surgery. The patient is trained to operate the Control Set and position the transmitter correctly over the receiver.
The prescribed impulses are completed each day and recorded in a distraction log. The lengthening schedule may be changed during treatment according to clinical reviews and X ray findings.
4. Physical Therapy and Follow Up
Physical therapy continues throughout the distraction phase to maintain range of motion and help the muscles and other soft tissues adapt to the increasing bone length.
Follow up includes clinical examination, regular X rays, review of the distraction log, pain management, and monitoring of joint movement, nerve function, and new bone formation.
5. Consolidation and Recovery
Once the planned length is reached, distraction stops and the new bone enters the consolidation phase. The regenerate bone gradually matures and becomes strong enough to accept more weight.
Partial weight bearing usually continues until X rays show adequate bone healing. Full weight bearing may take approximately 6 to 12 months, depending on the bone treated, the amount lengthened, and the rate of consolidation.
6. Implant Removal
The FITBONE nail and receiver are not designed to remain permanently. They are removed once consolidation is complete, commonly around 12 to 18 months after implantation.
Removal is performed as a separate procedure after X rays confirm sufficient healing.
Weight Bearing and Mobility
The Fitbone nail generally allows partial weight bearing during the distraction phase and early bone healing. A walker or crutches may be used for prescribed loading, transfers, and physiotherapy. After bilateral lengthening, a wheelchair may still be required for routine mobility.
Standing and assisted walking may begin early after surgery, but this should not be confused with full weight bearing. Exceeding the permitted load can damage the nail, particularly during the active lengthening phase.
Fitbone Assessment at ILLRC
Fitbone is not selected because a patient prefers an internal system or wishes to reach a particular height target. Assessment at ILLRC includes the reason for lengthening, standing alignment, bone dimensions, bone quality, joint movement, muscle flexibility, body weight, weight bearing requirements, and the expected rehabilitation period.
The final method and lengthening target are determined according to the patient’s anatomy, functional requirements, and ability to complete the full treatment and rehabilitation programme.
Request a Consultation
WHAT TO KNOW
Frequently Asked Questions
How much length can be achieved with Fitbone?
For stature lengthening, Fitbone may provide up to 8 cm through bilateral femoral lengthening. Tibial lengthening is usually kept around 5 cm because the muscles, tendons, nerves, and ankle tolerate less lengthening. The final target depends on bone formation, joint movement, and soft tissue tolerance rather than the maximum capacity of the implant.
How is the daily lengthening performed with Fitbone?
Lengthening usually begins five to ten days after surgery. The patient places an external transmitter on the skin over a small receiver implanted under the skin, and the energy it transmits drives the motor inside the nail. Lengthening is carried out in three to four sessions a day, giving a standard rate of about 1 mm per day. The daily rate is set by the surgeon and may be slowed or paused when required by X ray findings or the response of the bone and soft tissues.
Can Fitbone be used in both the femur and tibia?
Yes. Fitbone is designed for femoral and tibial lengthening. When a larger total height increase is planned, the femurs and tibias are usually treated in separate stages rather than lengthening one bone beyond its clinical tolerance.
Can I walk during the lengthening phase with Fitbone?
Fitbone allows limited weight bearing during distraction and early healing. A walker or crutches may be used for assisted standing, walking, and physiotherapy, while a wheelchair may still be needed for routine mobility after bilateral surgery. The permitted level of weight bearing depends on the implant, body weight, bone treated, and the surgeon’s instructions.
Why is physical therapy required during lengthening?
Physical therapy helps maintain joint movement and muscle flexibility as the bone becomes longer. It also reduces the risk of stiffness and contractures. Treatment continues during both the distraction and consolidation phases, with the programme adjusted according to movement, strength, and clinical findings.
Is the daily lengthening process painful?
The energy transfer from the transmitter is not normally felt. However, pain or tightness may occur as the muscles, nerves, and other soft tissues adapt to the increasing bone length. Symptoms are reviewed alongside joint movement, physical therapy progress, and X ray findings.
Does Fitbone leave scars on legs?
Yes. All limb lengthening surgery leaves surgical scars. Fitbone requires incisions for nail insertion, locking screws, the osteotomy, and receiver placement. It does not create the additional pin and wire scars associated with external fixation.
When can I walk with full weight on my legs after Fitbone surgery?
Full weight bearing can begin once X rays show that the new bone is strong enough. This is often after 4 to 6 months, depending on the bone treated, the amount lengthened, and healing progress.
When can I return to sports after Fitbone surgery?
You must first regain your range of motion and rebuild muscle strength. A return to sports may be possible from around six months after surgery, once X rays show sufficient bone healing and clinical review confirms that movement and strength are ready for increased activity.
Does the Fitbone implant need to be removed?
Yes. The nail and receiver are not designed for permanent implantation. They are removed after full consolidation, commonly about 12 to 18 months after the original surgery. The timing is confirmed through X rays and clinical assessment.
